144 lines
5.0 KiB
C
144 lines
5.0 KiB
C
/*
|
|
* Copyright (c) 2014-2016, Freescale Semiconductor, Inc.
|
|
* All rights reserved.
|
|
*
|
|
* Redistribution and use in source and binary forms, with or without modification,
|
|
* are permitted provided that the following conditions are met:
|
|
*
|
|
* o Redistributions of source code must retain the above copyright notice, this list
|
|
* of conditions and the following disclaimer.
|
|
*
|
|
* o Redistributions in binary form must reproduce the above copyright notice, this
|
|
* list of conditions and the following disclaimer in the documentation and/or
|
|
* other materials provided with the distribution.
|
|
*
|
|
* o Neither the name of Freescale Semiconductor, Inc. nor the names of its
|
|
* contributors may be used to endorse or promote products derived from this
|
|
* software without specific prior written permission.
|
|
*
|
|
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND
|
|
* ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
|
|
* WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
|
|
* DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR
|
|
* ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
|
|
* (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
|
|
* LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
|
|
* ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
|
|
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
|
|
* SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
|
|
*/
|
|
#ifndef __BOOTLOADER_CONFIG_H__
|
|
#define __BOOTLOADER_CONFIG_H__
|
|
|
|
////////////////////////////////////////////////////////////////////////////////
|
|
// Definitions
|
|
////////////////////////////////////////////////////////////////////////////////
|
|
|
|
//
|
|
// Bootloader configuration options
|
|
//
|
|
|
|
//! @name Peripheral configuration macros
|
|
//@{
|
|
|
|
#if !defined(BL_CONFIG_SCUART)
|
|
#define BL_CONFIG_SCUART (1)
|
|
#endif
|
|
#if !defined(BL_CONFIG_I2C)
|
|
#define BL_CONFIG_I2C (1)
|
|
#endif
|
|
#if !defined(BL_CONFIG_DSPI)
|
|
#define BL_CONFIG_DSPI (1)
|
|
#endif
|
|
#if !defined(BL_CONFIG_USB_HID)
|
|
#define BL_CONFIG_USB_HID (1)
|
|
#endif
|
|
#if !defined(BL_CONFIG_USB_MSC)
|
|
#define BL_CONFIG_USB_MSC (1)
|
|
#endif
|
|
|
|
//@}
|
|
|
|
#if !defined(BL_TARGET_FLASH) && !defined(BL_TARGET_RAM)
|
|
#define BL_TARGET_FLASH (1)
|
|
#endif
|
|
|
|
#define BL_FEATURE_FLASH_CHECK_CUMULATIVE_WRITE (1)
|
|
|
|
#if defined(BL_TARGET_RAM)
|
|
#define BL_FEATURE_FLASH_SECURITY (0)
|
|
#else
|
|
#define BL_FEATURE_FLASH_SECURITY (1)
|
|
#endif
|
|
|
|
#define BL_FEATURE_QSPI_MODULE (0)
|
|
|
|
#define BL_FEATURE_ENCRYPTION_MMCAU (1)
|
|
#define BL_FEATURE_ENCRYPTION (BL_FEATURE_ENCRYPTION_MMCAU)
|
|
#define BL_FEATURE_ENCRYPTION_KEY_ADDRESS 0xb000 // NOTE: this address must be 4-byte aligned.
|
|
|
|
#define BL_FEATURE_MIN_PROFILE (0)
|
|
|
|
// Bootloader peripheral detection default timeout in milliseconds
|
|
// After coming out of reset the bootloader will spin in a peripheral detection
|
|
// loop for this amount of time. A zero value means no time out.
|
|
#if DEBUG
|
|
#define BL_DEFAULT_PERIPHERAL_DETECT_TIMEOUT 0
|
|
#else
|
|
#define BL_DEFAULT_PERIPHERAL_DETECT_TIMEOUT 5000
|
|
#endif // DEBUG
|
|
|
|
#define BL_FEATURE_POWERDOWN (0)
|
|
|
|
// Bootloader powerdown timeout in milliseconds
|
|
// The bootloader enters a low power mode after waiting for this amount of time. A zero value means // no time out. Only
|
|
// applicable if BL_FEATURE_POWERDOWN is enabled.
|
|
#if DEBUG
|
|
#define BL_DEFAULT_POWERDOWN_TIMEOUT 10000
|
|
#else
|
|
#define BL_DEFAULT_POWERDOWN_TIMEOUT 600000
|
|
#endif // DEBUG
|
|
|
|
#if !defined(BL_TARGET_RAM)
|
|
#define BL_FEATURE_CRC_CHECK (1)
|
|
#endif
|
|
|
|
#define BL_FEATURE_UART_AUTOBAUD_IRQ (1)
|
|
|
|
#define BL_FEATURE_ENABLE_FLASH_PROGRAM_SECTION (1)
|
|
|
|
// The bootloader will check this address for the application vector table upon startup.
|
|
#if !defined(BL_APP_VECTOR_TABLE_ADDRESS)
|
|
#define BL_APP_VECTOR_TABLE_ADDRESS 0xa000
|
|
#endif
|
|
|
|
/* Serial Port Info */
|
|
|
|
/**************************************************************************
|
|
* Note:
|
|
*
|
|
* Because of the changes to the UART modules, we can no longer define
|
|
* the TERM_PORT as a base pointer. The uart functions have been modified
|
|
* accommodate this change. Now, TERM_PORT_NUM must be defined as the
|
|
* number of the UART port desired to use
|
|
*
|
|
* TERM_PORT_NUM = 0 -- This allows you to use UART0; default pins are
|
|
* PTA14 and PTA15
|
|
*
|
|
* TERM_PORT_NUM = 1 -- This allows you to use UART1; default pins are
|
|
* PTC3 and PTC4
|
|
*
|
|
* TERM_PORT_NUM = 2 -- This allows you to use UART2; default pins are
|
|
* PTD2 and PTD3
|
|
*
|
|
*************************************************************************/
|
|
#define TERM_PORT_NUM 0
|
|
|
|
#define TERMINAL_BAUD 19200
|
|
#undef HW_FLOW_CONTROL
|
|
|
|
#endif // __BOOTLOADER_CONFIG_H__
|
|
////////////////////////////////////////////////////////////////////////////////
|
|
// EOF
|
|
////////////////////////////////////////////////////////////////////////////////
|