/*
* Copyright (c) 2014-2015, Freescale Semiconductor, Inc.
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without modification,
* are permitted provided that the following conditions are met:
*
* o Redistributions of source code must retain the above copyright notice, this list
*   of conditions and the following disclaimer.
*
* o Redistributions in binary form must reproduce the above copyright notice, this
*   list of conditions and the following disclaimer in the documentation and/or
*   other materials provided with the distribution.
*
* o Neither the name of Freescale Semiconductor, Inc. nor the names of its
*   contributors may be used to endorse or promote products derived from this
*   software without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND
* ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
* WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
* DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR
* ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
* (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
* LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
* ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
* SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*/
#ifndef __BOOTLOADER_CONFIG_H__
#define __BOOTLOADER_CONFIG_H__

////////////////////////////////////////////////////////////////////////////////
// Definitions
////////////////////////////////////////////////////////////////////////////////

//
// Bootloader configuration options
//

//! @name Peripheral configuration macros
//@{

#if !defined(BL_CONFIG_UART)
#define BL_CONFIG_UART (1)
#endif
#if !defined(BL_CONFIG_SCUART)
#define BL_CONFIG_SCUART (1)
#endif
#if !defined(BL_CONFIG_LPUART)
#define BL_CONFIG_LPUART (1)
#endif

#if !defined(BL_CONFIG_CAN)
#define BL_CONFIG_CAN (1)
#endif

#if !defined(BL_CONFIG_I2C)
#define BL_CONFIG_I2C (1)
#endif

#if !defined(BL_CONFIG_SPI)
#define BL_CONFIG_SPI (1)
#endif
#if !defined(BL_CONFIG_DSPI)
#define BL_CONFIG_DSPI (1)
#endif

#if !defined(BL_CONFIG_USB)
#define BL_CONFIG_USB (1)
#endif
#if !defined(BL_CONFIG_USB_HID)
#define BL_CONFIG_USB_HID (0)
#endif
#if !defined(BL_CONFIG_USB_MSC)
#define BL_CONFIG_USB_MSC (1)
#endif

#if !defined(BL_CONFIG_USB_HID)
#define BL_CONFIG_USB_HID (1)
#endif
#if !defined(BL_CONFIG_HS_USB_HID)
#define BL_CONFIG_HS_USB_HID (0) // For TOWER and FRDM boards
#endif

#if !defined(BL_CONFIG_HS_USB_MSC)
#define BL_CONFIG_HS_USB_MSC (1) // For TOWER and FRDM boards
#endif
//@}

#if !defined(BL_TARGET_FLASH) && !defined(BL_TARGET_RAM)
#define BL_TARGET_FLASH (1)
#endif

#if !defined(BL_TARGET_RAM)
#define BL_FEATURE_CRC_CHECK (1)
#endif

#define BL_FEATURE_QSPI_MODULE (0)

#define BL_FEATURE_ENCRYPTION (1)

#define BL_FEATURE_UART_AUTOBAUD_IRQ (1)

// Bootloader peripheral detection default timeout in milliseconds
// After coming out of reset the bootloader will spin in a peripheral detection
// loop for this amount of time. A zero value means no time out.
#if DEBUG
#define BL_DEFAULT_PERIPHERAL_DETECT_TIMEOUT 0
#else
#define BL_DEFAULT_PERIPHERAL_DETECT_TIMEOUT 5000
#endif // DEBUG

#define BL_FEATURE_POWERDOWN (0)

// Bootloader powerdown timeout in milliseconds
// The bootloader enters a low power mode after waiting for this amount of time. A zero value means // no time out. Only
// applicable if BL_FEATURE_POWERDOWN is enabled.
#if DEBUG
#define BL_DEFAULT_POWERDOWN_TIMEOUT 10000
#else
#define BL_DEFAULT_POWERDOWN_TIMEOUT 600000
#endif // DEBUG

// The bootloader will check this address for the application vector table upon startup.
#if !defined(BL_APP_VECTOR_TABLE_ADDRESS)
#define BL_APP_VECTOR_TABLE_ADDRESS 0xa000
#endif

/* Serial Port Info */

/**************************************************************************
 * Note:
 *
 * Because of the changes to the UART modules, we can no longer define
 * the TERM_PORT as a base pointer.  The uart functions have been modified
 * accommodate this change.  Now, TERM_PORT_NUM must be defined as the
 * number of the UART port desired to use
 *
 * TERM_PORT_NUM = 0  -- This allows you to use UART0; default pins are
 *                        PTA14 and PTA15
 *
 * TERM_PORT_NUM = 1  -- This allows you to use UART1; default pins are
 *                        PTC3 and PTC4
 *
 * TERM_PORT_NUM = 2  -- This allows you to use UART2; default pins are
 *                        PTD2 and PTD3
 *
 *************************************************************************/
#define TERM_PORT_NUM 0

#define TERMINAL_BAUD 19200
#undef HW_FLOW_CONTROL

#endif // __BOOTLOADER_CONFIG_H__
////////////////////////////////////////////////////////////////////////////////
// EOF
////////////////////////////////////////////////////////////////////////////////