Add KBOOT.

targets/MK65F18/src/bootloader_config.h

@@ -0,0 +1,156 @@
+/*
+* Copyright (c) 2014-2015, Freescale Semiconductor, Inc.
+* All rights reserved.
+*
+* Redistribution and use in source and binary forms, with or without modification,
+* are permitted provided that the following conditions are met:
+*
+* o Redistributions of source code must retain the above copyright notice, this list
+*   of conditions and the following disclaimer.
+*
+* o Redistributions in binary form must reproduce the above copyright notice, this
+*   list of conditions and the following disclaimer in the documentation and/or
+*   other materials provided with the distribution.
+*
+* o Neither the name of Freescale Semiconductor, Inc. nor the names of its
+*   contributors may be used to endorse or promote products derived from this
+*   software without specific prior written permission.
+*
+* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND
+* ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+* WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+* DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR
+* ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+* (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+* LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
+* ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+* SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+*/
+#ifndef __BOOTLOADER_CONFIG_H__
+#define __BOOTLOADER_CONFIG_H__
+
+////////////////////////////////////////////////////////////////////////////////
+// Definitions
+////////////////////////////////////////////////////////////////////////////////
+
+//
+// Bootloader configuration options
+//
+
+//! @name Peripheral configuration macros
+//@{
+
+#if !defined(BL_CONFIG_SCUART)
+#define BL_CONFIG_SCUART (1)
+#endif
+#if !defined(BL_CONFIG_I2C)
+#define BL_CONFIG_I2C (1)
+#endif
+#if !defined(BL_CONFIG_DSPI)
+#define BL_CONFIG_DSPI (1)
+#endif
+
+/* Either FS USB or HS USB to be enabled, not both are enabled at the same time.
+ * HS USB is not supported in flashloader build, due to extral dependence.     */
+#if !defined(BL_CONFIG_USB_HID)
+#define BL_CONFIG_USB_HID (1)
+#endif
+#if !defined(BL_CONFIG_USB_MSC)
+#define BL_CONFIG_USB_MSC (1)
+#endif
+
+#if !defined(BL_CONFIG_HS_USB_HID)
+#define BL_CONFIG_HS_USB_HID (0) // For TOWER and FRDM boards
+#endif
+#if !defined(BL_CONFIG_HS_USB_MSC)
+#define BL_CONFIG_HS_USB_MSC (0) // For TOWER and FRDM boards
+#endif
+//@}
+
+#if !defined(BL_TARGET_FLASH) && !defined(BL_TARGET_RAM)
+#define BL_TARGET_FLASH (1)
+#endif
+
+#if defined(BL_TARGET_RAM)
+#define BL_FEATURE_FLASH_SECURITY (0)
+#else
+#define BL_FEATURE_FLASH_SECURITY (1)
+#endif
+
+#if !defined(BL_TARGET_RAM)
+#define BL_FEATURE_CRC_CHECK (1)
+#endif
+
+#define BL_FEATURE_QSPI_MODULE (0)
+
+#define BL_FEATURE_ENCRYPTION_MMCAU (1)
+#define BL_FEATURE_ENCRYPTION (BL_FEATURE_ENCRYPTION_MMCAU)
+#define BL_FEATURE_ENCRYPTION_KEY_ADDRESS 0xb000 // NOTE: this address must be 4-byte aligned.
+
+#define BL_FEATURE_UART_AUTOBAUD_IRQ (1)
+
+// Bootloader peripheral detection default timeout in milliseconds
+// After coming out of reset the bootloader will spin in a peripheral detection
+// loop for this amount of time. A zero value means no time out.
+#if DEBUG
+#define BL_DEFAULT_PERIPHERAL_DETECT_TIMEOUT 0
+#else
+#define BL_DEFAULT_PERIPHERAL_DETECT_TIMEOUT 5000
+#endif // DEBUG
+
+#define BL_FEATURE_POWERDOWN (0)
+
+// Bootloader powerdown timeout in milliseconds
+// The bootloader enters a low power mode after waiting for this amount of time. A zero value means // no time out. Only
+// applicable if BL_FEATURE_POWERDOWN is enabled.
+#if DEBUG
+#define BL_DEFAULT_POWERDOWN_TIMEOUT 10000
+#else
+#define BL_DEFAULT_POWERDOWN_TIMEOUT 600000
+#endif // DEBUG
+
+// The bootloader will check this address for the application vector table upon startup.
+#if !defined(BL_APP_VECTOR_TABLE_ADDRESS)
+#define BL_APP_VECTOR_TABLE_ADDRESS 0xa000
+#endif
+
+/* Backup application Info */
+#if !defined(BL_TARGET_RAM)
+#define BL_FEATURE_RELIABLE_UPDATE (1)
+#define BL_FEATURE_HARDWARE_SWAP_UPDATE (1)
+// Note the BAKCUP APP START address must be sector-aligned.
+#define BL_BACKUP_APP_START (0x105000)
+#endif // BL_TARGET_RAM
+
+#define BL_FEATURE_ENABLE_FLASH_PROGRAM_SECTION (1)
+
+/* Serial Port Info */
+
+/**************************************************************************
+ * Note:
+ *
+ * Because of the changes to the UART modules, we can no longer define
+ * the TERM_PORT as a base pointer.  The uart functions have been modified
+ * accommodate this change.  Now, TERM_PORT_NUM must be defined as the
+ * number of the UART port desired to use
+ *
+ * TERM_PORT_NUM = 0  -- This allows you to use UART0; default pins are
+ *                        PTA14 and PTA15
+ *
+ * TERM_PORT_NUM = 1  -- This allows you to use UART1; default pins are
+ *                        PTC3 and PTC4
+ *
+ * TERM_PORT_NUM = 2  -- This allows you to use UART2; default pins are
+ *                        PTD2 and PTD3
+ *
+ *************************************************************************/
+#define TERM_PORT_NUM 0
+
+#define TERMINAL_BAUD 19200
+#undef HW_FLOW_CONTROL
+
+#endif // __BOOTLOADER_CONFIG_H__
+////////////////////////////////////////////////////////////////////////////////
+// EOF
+////////////////////////////////////////////////////////////////////////////////